Advertisement
    Home        Articles        Reviews        Gallery        Contests        Forums     Search Login
Forums
 Introduction
 Posting guidelines
 Forum key
New Messages
Forum List
 News Forums
   GeneralOct 12 
   IndustryOct 12 
   Shows & ClubsOct 12 
 Site Forums
   ArticlesMay 16
   Build LogsOct 12
   ReviewsSep 22
   GalleryOct 12
   ContestsOct 6
 Modelling Forums
   KitsOct 9 
   ConstructionOct 12 
   PaintingOct 10 
   FiguresOct 10 
   DioramasAug 29 
   1-48th ScaleOct 1 
   Small ScaleSep 23 
 Research Forums
   WW2Oct 12 
   Post WW2Oct 10 
   Pre WW2Sep 6 
 Classifieds Ads
   Buy & SellOct 12 
   CommercialOct 10 
 

Forums - Site / Build Logs

Messages in this Build Logs forum are automatically posted when new Build Logs or Chapters are added. Other modellers can then comment on them. Refer to the Build Logs section for more information.

Topics  81
Messages  3066
 Subject:  [Chapter] Chapter 22 - KaltluftgrätingList thread.  
  
 Date:  Jul 16, 2004
 From:  James Tainton 
Chapter 22 - Kaltluftgräting

Pictures 1. and 2.Here you can see in the photos that I have not used the rear air intake cover supplied with the Tristar resin detail set- too many clean up problems. So what I did was use the plastic kit one, cut from the discarded rear half from a previous step. This was sanded thin in profile and made to fit into the space on the rear superstructure deck. I also hollowed out the solid slating that was on the plastic cover and replaced this with thin plastic Evergreen strips. This all looked a lot cleaner than the one in the resin kit. Next I cut the hinges from the resin cover, as the ones on the plastic version were destroyed in the salvaging act. These little tabs were glued in place on the cover frame and the unit was set aside. As I was building this project Aber came out with a detail set (or two) that I wish I had . There is a air intake grating provided there that is more detailed as well as the hinges. Oh well - next time.

Picture 3. shows the completed Lion Roar support bar for the suspension in place.

Pictures 4., 5. and 6. show the construction of the exhaust system. The replacement resin exhaust tubes and the mufflers from the plastic kit are combined to create this. You can see that I have had to remove the plastic "tube" from the muffler. I then drilled a hole in the muffler end to accept the resin tube. This all was tweaked while in place on the engine and fender before gluing permanently, to ensure proper alignment.

In image 6. one can also see the gas mask canisters have been painted and detailed as well the gas tanks have been further aged and weathered.
 
Thread Listing 
  [BLOG] Panzerkampfwagen I (Sd.Kfz.101) Ausfuehrung A - James Tainton - Mar 18, 2004
. . . [Chapter] Chapter 1. - Roll Call - James Tainton - Mar 18, 2004
. . . . . . Re: [Chapter] Chapter 1. - Roll Call - Christophe Jacquemont - Mar 19, 2004
. . . . . . . . . Re: [Chapter] Chapter 1. - Roll Call - James Tainton - Mar 21, 2004
. . . [Chapter] Chapter 2 - Getting the Goods on Panzer Is - James Tainton - Mar 19, 2004
. . . [Chapter] Chapter 3. - Making Tracks - James Tainton - Mar 21, 2004
. . . [Chapter] Chapter 4 - Transmission, Clutch, Steering Unit - James Tainton - Mar 22, 2004
. . . [Chapter] Chapter 5. - Body, Side and Driver Seat - James Tainton - Mar 23, 2004
. . . [Chapter] Chapter 6 - Growth on the Inside - James Tainton - Mar 25, 2004
. . . [Chapter] Chapter 7 - The Mechanical Guts - James Tainton - Mar 29, 2004
. . . [Chapter] Chapter 8 - A Little Nip and Tuck - James Tainton - Apr 2, 2004
. . . [Chapter] Chapter 9 - Weathering and Transmission Access - James Tainton - Apr 17, 2004
. . . [Chapter] Chapter 10 - More Bits - James Tainton - Apr 19, 2004
. . . [Chapter] Chapter 11 - Aber Vision Ports - James Tainton - Apr 24, 2004
. . . . . . Re: [Chapter] Chapter 11 - Aber Vision Ports - Robert Lu - Apr 24, 2004
. . . [Chapter] Chapter 12 - More Vision Ports - James Tainton - Apr 26, 2004
. . . [Chapter] Chapter 13 - More Vision Port Fixings - James Tainton - Apr 28, 2004
. . . [Chapter] Chapter 14 - Mr. Surfacer and Off White - James Tainton - May 3, 2004
. . . [Chapter] Chapter 15 - More Work on the Interior - James Tainton - May 4, 2004
. . . [Chapter] Chapter 16 - Klapp for the Wolfmensch - James Tainton - May 24, 2004
. . . [Chapter] Chapter 17 - Hull Covers Done - James Tainton - May 27, 2004
. . . [Chapter] Chapter 18 - Nice wheels, man. - James Tainton - Jun 5, 2004
. . . [Chapter] Chapter 19 - Progress Pictures - James Tainton - Jun 7, 2004
. . . [Chapter] Chapter 20 - Drilling makes perfect... - James Tainton - Jun 9, 2004
. . . [Chapter] Chapter 21 - These Bolt Heads Will Drive You Nuts - James Tainton - Jun 14, 2004
. . . [Chapter] Chapter 22 - Kaltluftgräting - James Tainton - Jul 16, 2004
. . . [Chapter] Chapter 23 - Exhausts and aging. - James Tainton - Aug 7, 2004
. . . [Chapter] Chapter 24 - Top meets bottom - James Tainton - Aug 16, 2004
. . . [Chapter] Chapter 25 - I have got a one track mind. - James Tainton - Aug 20, 2004
. . . . . . Re: [Chapter] Chapter 25 - I have got a one track mind. - Erik Forsgren - Dec 31, 2005
    Home        Articles        Reviews        Gallery        Contests        Forums     Contact Track-Link