Advertisement
    Home        Articles        Reviews        Gallery        Contests        Forums     Search Login
Forums
 Introduction
 Posting guidelines
 Forum key
New Messages
Forum List
 News Forums
   GeneralOct 16 
   IndustryOct 16 
   Shows & ClubsOct 15 
 Site Forums
   ArticlesMay 16
   Build LogsOct 16
   ReviewsSep 22
   GalleryOct 16
   ContestsOct 15
 Modelling Forums
   KitsOct 16 
   ConstructionOct 15 
   PaintingOct 16 
   FiguresOct 10 
   DioramasOct 14 
   1-48th ScaleOct 13 
   Small ScaleSep 23 
 Research Forums
   WW2Oct 16 
   Post WW2Oct 16 
   Pre WW2Sep 6 
 Classifieds Ads
   Buy & SellOct 16 
   CommercialOct 16 
 

Forums - Site / Build Logs

Messages in this Build Logs forum are automatically posted when new Build Logs or Chapters are added. Other modellers can then comment on them. Refer to the Build Logs section for more information.
Topics  81
Messages  3071
 Subject:  [Chapter 1] The Lower Hull - Tub AssemblyList thread.  
  
 Date:  May 11, 2006
 From:  Paul A. Owen 
The Lower Hull - Tub Assembly

The lower hull consists of a bottom part, two sides and a front and rear plate. There are also two internal braces for strengthening. I found assembly a little tricky, after several dry runs with tape and rubber bands the following sequence worked the best.

I first cleaned up the bottom (part F-1), it was a little warped but this will correct itself as the hull is assembled. I was careful to clean the edges that mate to the hull sides, not doing so will result in a gap. I then added the two internal braces (parts E-1), these fit snuggly without much play but it is important to make sure they sit perpendicular to the hull floor. I sealed the joins with Cyanoacrylate (CA) glue (popularly know as "Krazy Glue"). Next the side walls were cleaned up, again it is very important to remove any leftover sprue attachment nubs as these will interfere with the fit. Now these where attached to the lower hull I applied glue ONLY to the internal brace arms and let this set. Next, after this had set, I glued in the front and rear.

After all this had set I strengthened the joint by gluing strips of styrene along the joins from the inside of the hull. These are evident in the photographs. The resulting "tub" is now quite solid and work to clean up the front and rear joins can begin.
 
Thread Listing 
  [BLOG] Tristar Panzer IV Ausf. C - Paul A. Owen - May 11, 2006
. . . [Chapter 1] The Lower Hull - Tub Assembly - Paul A. Owen - May 11, 2006
. . . [Chapter 2] Lower Hull Front - short shot corrections - Paul A. Owen - May 14, 2006
. . . . . . Lower Hull Front - Zusatzpanzerung [IMG] - Paul A. Owen - May 14, 2006
. . . [Chapter 3] Lower Hull - Rear - Paul A. Owen - May 23, 2006
. . . . . . Re: [Chapter 3] Lower Hull - Rear [IMG] - Paul A. Owen - May 23, 2006
. . . [Chapter 4] Fixing the Upper Hull - Paul A. Owen - Aug 19, 2006
. . . . . . Re: [Chapter 4] Fixing the Upper Hull [IMG] - Paul A. Owen - Aug 19, 2006
. . . . . . Re: [Chapter 4] Fixing the Upper Hull - Chris Oldfield - Aug 23, 2006
. . . . . . . . . Re: [Chapter 4] Fixing the Upper Hull - Paul A. Owen - Aug 23, 2006
. . . . . . . . . . . . Re: [Chapter 4] Fixing the Upper Hull - Chris Oldfield - Aug 24, 2006
. . . [Chapter] Hull Side Engine Vents - Paul A. Owen - Dec 9, 2006
. . . . . . Re: [Chapter] Hull Side Engine Vents - Photo #2 [IMG] - Paul A. Owen - Dec 9, 2006
. . . . . . . . . Re: [Chapter] Hull Side Engine Vents - Photo #2 - Bob layton - Dec 11, 2006
. . . . . . . . . . . . ... Aber fenders - Paul A. Owen - Dec 11, 2006
. . . . . . Re: [Chapter] Hull Side Engine Vents - Photo #3 [IMG] - Paul A. Owen - Dec 9, 2006
. . . . . . . . . little bolts - Saul Garcia - Dec 10, 2006
. . . . . . . . . . . . Re: little bolts - Paul A. Owen - Dec 10, 2006
. . . Re: [BLOG] Tristar Panzer IV Ausf. C - Ian Flockhart - Dec 12, 2006
. . . . . . Re: [BLOG] Tristar Panzer IV Ausf. C - Paul A. Owen - Dec 12, 2006
. . . [Chapter] Bogie Assembly - Paul A. Owen - Dec 15, 2006
. . . . . . Re: [Chapter] Bogie Assembly - Photo #2 [IMG] - Paul A. Owen - Dec 15, 2006
. . . . . . Re: [Chapter] Bogie Assembly - Photo #3 [IMG] - Paul A. Owen - Dec 15, 2006
. . . . . . Re: [Chapter] Bogie Assembly - Photo #4 [IMG] - Paul A. Owen - Dec 15, 2006
. . . . . . wheel spacing?? - Glenn Bartolotti - Dec 15, 2006
. . . . . . . . . Re: wheel spacing?? - Paul A. Owen - Dec 15, 2006
. . . . . . . . . Wheels are not spaced evenly on the real Pz IV... - Kazutaka YOKOTA - Dec 28, 2006
. . . . . . . . . . . . Re: Wheels are not spaced evenly on the real Pz IV... - Glenn Bartolotti - Dec 28, 2006
. . . . . . road wheel Continental marking - Bob Layton - Dec 15, 2006
. . . . . . . . . Re: road wheel Continental marking - Paul A. Owen - Dec 15, 2006
. . . . . . . . . . . . road wheels not aligned correct???? - Glenn Bartolotti - Dec 24, 2006
. . . . . . . . . . . . . . . Did you see this Paul????? - Glenn Bartolotti - Dec 28, 2006
. . . . . . . . . . . . . . . Re: road wheels not aligned correct???? - Paul A. Owen - Dec 28, 2006
. . . . . . . . . . . . . . . . . . Re: road wheels not aligned correct???? - Glenn Bartolotti - Dec 28, 2006
. . . . . . . . . . . . . . . . . . . . . Re: road wheels not aligned correct???? - glenn Bartolotti - Dec 28, 2006
. . . [Chapter] Weld Beads - Paul A. Owen - Feb 11, 2008
    Home        Articles        Reviews        Gallery        Contests        Forums     Contact Track-Link